玻璃門作為門這一大類中，使用場所多，安裝數量多。也就導致很多客戶朋友們在日常使用玻璃門時經常會遇到各種各樣的故障。那么作為一家玻璃門維修公司小編，在日常對玻璃門維修時會用到哪些方法呢？濟南電動卷簾門安裝維修小編就通過本文給大家介紹一下玻璃門中的維修方法步驟。

Glass doors, as a major category of doors, are widely used and have a large number of installations. This has led to many customers often encountering various malfunctions when using glass doors in their daily lives. So, as the editor of a glass door maintenance company, what methods are used in daily glass door maintenance? The installation and maintenance of Jinan electric Roller shutter will introduce the maintenance methods and steps in the glass door through this article.

一看

Take a look

即查看

View Now

是否有配件受損

Are there any damaged accessories

如配件斷裂、發黑發黃、引腳相碰、器件松動、連線錯誤等。某些接觸不良故障，尤其是在電源通電后，因故障點接觸不良而產生火花。所以就認真看的相關配件有無出現損壞。

Such as broken accessories, black and yellow hair, pin collisions, loose components, incorrect wiring, etc. Some poor contact faults, especially sparks generated due to poor contact at the fault point after power is applied. So I carefully checked if there was any damage to the relevant accessories.

二聽

Second Listening

即聽運行的聲音

Listen to the sound of operation immediately

檢查是否有配件受損

Check if any accessories are damaged

在控制系統中，大都采用了電磁繼電器作為控制器件，在繼電器觸點切換時會產生清晰的“滴噠”聲。如無聲或異常，在確定繼電器驅動電器無故障后，可判定該繼電器不良。如果有摩擦聲檢查軌道、吊輪、門扇等部分，查看這些部分配件的磨損情況。磨損嚴重會產生摩擦聲應及時更換維修相關配件。

In control systems, electromagnetic relays are mostly used as control devices, which produce a clear "clicking" sound when the relay contacts switch. If there is no sound or abnormality, it can be determined that the relay is faulty after confirming that there is no fault in the relay driving device. If there is friction sound, check the track, lifting wheel, door leaf, and other parts to see if they are worn. Severe wear and tear can cause friction noise, and relevant accessories should be replaced and repaired in a timely manner.

三摸

Three touch

即觸摸配件

I.e. touch accessories

檢查是否有配件受損

Check if any accessories are damaged

在的維修過程中，也經常在通電后用手摸某些配件。如穩壓IC等集成器件、防雷管、變壓器、驅動二極管等等。以便感覺其溫度是否正常，如發熱快、溫度高、電路無短路故障則可斷定器件不良。

During the maintenance process, it is also common to touch certain accessories with your hands after power is applied. Integrated devices such as voltage stabilizing ICs, lightning protection tubes, transformers, drive diodes, etc. In order to feel whether the temperature is normal, if the heating is fast, the temperature is high, and there is no short circuit fault in the circuit, it can be determined that the device is defective.

四測

Four measurements

即測量控制電路

I.e. measurement control circuit

檢查是否有配件受損

Check if any accessories are damaged

通常采用的方式有測電壓、測電路的電阻、測電流等。這是一種綜合性邏輯分析手段,可依據各種測量的數據準確地找出故障原因及損壞器件。

The commonly used methods include voltage measurement, circuit resistance measurement, current measurement, etc. This is a comprehensive logical analysis method that can accurately identify the cause of faults and damaged devices based on various measured data.

日常如上門維修時，除了詢問客戶在出現故障前后有哪些表現，還有就是要進行以下四個步驟了，就是看、聽、摸、測。以上內容希望能夠幫助到您，還有什么事項就來我們網站http://luoboyy.com咨詢！

When conducting daily on-site maintenance, in addition to asking customers about their performance before and after a malfunction occurs, there are also four steps that need to be carried out: look, listen, touch, and test. I hope the above content can help you. If you have any further matters, please come to our website http://luoboyy.com consulting service