濟南車庫門：車庫門遙控器對碼的方法和注意事項

來源：http://luoboyy.com/  發布時間：2024-05-10 11:48:19

　　有了車庫直觀的感受就是冬天不用“熱車”，夏天不用“蒸桑拿”，不用為找車位而煩惱。但日常使用中難免會丟失車庫遙控器，是找人維修還是自己動手？其實增配遙控器非常簡單，只要學會對碼就能輕松。對碼是車庫遙控器增配過程中非常重要的一環，下面我們就介紹一下車庫門遙控器對碼的方法和注意事項。

The most intuitive feeling with a garage is that you don't have to use a hot car in winter, take a sauna in summer, or worry about finding a parking spot. But it is inevitable to lose the garage remote control in daily use. Should we seek professional repair or do we have to do it ourselves? Actually, adding a remote control is very simple, as long as you learn to match the code, it can be easily solved. Code matching is a very important part of the process of adding a garage remote control. Below, we will introduce the method and precautions for code matching of garage door remote controls.

　　一、準備工作

1、 Preparation work

　　從某寶上花十幾塊錢買個一樣的遙控器。準備個板凳要不然夠不著電機盒。對碼之前車庫門處于關閉狀態。

Spend more than ten yuan on a certain treasure to buy the same remote control. Prepare a stool, otherwise you won't be able to reach the motor box. The garage door was closed before the code was checked.

　　二、對碼步驟

2、 Matching steps

　　1. 找到電機盒外殼上的“SHUTTER（百葉窗）”字樣，在字樣上方有上下兩個箭頭，分別對應遙控器的上下鍵。有的需要打開電機盒，電路板上有控制上下鍵的按鈕。

1. Find the word "SHUTTER" on the outer shell of the motor box, with two arrows above the word, corresponding to the up and down keys of the remote control. Some require opening the motor box, and there are buttons on the circuit board that control the up and down buttons.

　　2. 按住電機盒的兩個按鍵，旁邊的指示燈會開始閃爍，表示電機盒已經準備就緒。

2. Press and hold the two buttons on the motor box, and the indicator light next to it will start flashing, indicating that the motor box is ready.

　　3. 再次按下手中遙控器的上下鍵，此時電機盒的指示燈會停止閃爍，表示對碼成功。

3. Press the up and down buttons on the remote control again, and the indicator light on the motor box will stop flashing, indicating successful code matching.

　　4. 重復以上步驟，依次對其他遙控器進行對碼即可。多準備幾個以備不時之需。

4. Repeat the above steps and code the other remote controls one by one. Prepare more for unexpected needs.

　　三、注意事項

3、 Precautions

　　1. 在對碼過程中，不要同時按下遙控器的其他按鍵，以免干擾對碼過程。

1. During the coding process, do not press other buttons on the remote control at the same time to avoid interfering with the coding process.

　　2. 如果對碼不成功，可以重新嘗試或者檢查電機是否工作正常。

If the code matching is not successful, you can try again or check if the motor is working properly.

　　3. 在使用遙控器控制車庫門時，要確保遙控器和電機匹配一致，避免誤控他人車庫。

When using a remote control to control the garage door, it is important to ensure that the remote control matches the motor to avoid accidentally controlling someone else's garage.

　　如果是有自動拷貝功能的，準備新舊兩把遙控器，長按舊遙控器上下鍵三秒，指示燈閃爍后松開。然后交替按下新舊遙控器的各個按鍵，也能匹配成功。就是清碼和拷貝兩個步驟。

If there is an automatic copying function, prepare two new and old remote controls. First, press and hold the up and down buttons on the old remote control for three seconds, the indicator light will flash, and then release it. Then press the various buttons of the new and old remote controls alternately, and the matching can also be successful. It consists of two steps: clearing the code and copying.

　　車庫門遙控器的對碼步驟雖然簡單，只要正確對碼，就能讓遙控器正?？刂栖噹扉T的開關。在使用遙控器時，需要認真閱讀說明書，了解對碼方法和注意事項，確保使用車庫門遙控器。

Although the coding process for the garage door remote control is simple, as long as the coding is correct, the remote control can control the opening and closing of the garage door normally. When using the remote control, it is necessary to carefully read the manual, understand the code matching method and precautions, and ensure safe use of the garage door remote control.

本文由濟南車庫門為您精心提供，如想了解更多請點擊我們的網站：http://luoboyy.com，我們將會以的熱情為您解答！

This article is carefully provided by Jinan Garage Door. If you want to learn more, please click on our website: http://luoboyy.com We will answer you with the greatest enthusiasm!