電動卷簾門故障與哪些部件有關系？

來源：http://luoboyy.com/  發布時間：2024-01-16 11:40:45

電動卷簾門的電機與卷筒芯軸之間是由傳動鏈條來連接,電機地腳用螺釘固定在鏈輪支架板上。替換電機前,必須將卷簾門降低端或用支架將卷簾門撐住。這是由于一是卷簾門的制動是靠電機本體上的制動器來起作用,電機撤除后,卷簾門則沒有制動而主動下滑;二是可以使傳動鏈條放松,便利將鏈條取下。

The motor of the electric roller shutter door is connected to the drum core shaft by a transmission chain, and the motor foot is fixed on the sprocket support plate with screws. Before replacing the motor, the roller shutter door must be lowered to the low end or supported by a bracket. This is because firstly, the braking of the roller shutter door relies on the brake on the motor body. After the motor is removed, the roller shutter door does not brake and actively slides down; Secondly, it can relax the transmission chain and facilitate the removal of the chain.

替換電機的過程:將電機接線做好符號然后撤除,將電機地腳螺絲擰松將傳動鏈條摘下,終將電機地腳螺絲撤除將電機取出;新電機裝置次序相反,但要留意,電機裝置好后,其本體上的環形手拉鏈條應天然筆直向下,不得有卡阻景象。

The process of replacing the motor: Mark the motor wiring and remove it, loosen the motor foundation screw to remove the transmission chain, and finally remove the motor foundation screw to remove it; The order of the new motor device is opposite, but it should be noted that after the motor device is installed, the circular zipper strip on its body should be naturally straight downwards without any jamming phenomenon.

操控失效故障發作的部位及因素:.繼電器(接觸器)觸點粘死行程微動開關失效 或觸片變形滑塊緊定螺釘松靠板螺絲松使靠板移位,使滑塊或螺母不能隨絲

The location and factors causing the occurrence of control failure faults: relay (contactor) contact sticking, stroke micro switch failure or contact deformation, slider tightening screw loosening, support plate screw loosening, causing the support plate to shift, preventing the slider or nut from following the thread

桿轉動而移動限位器傳動齒輪破損按鈕上下鍵卡死。

The transmission gear of the limit switch is damaged due to the rotation of the rod, and the up and down buttons are stuck.

二電動卷簾門安裝

Installation of electric roller shutter doors

先在需求裝置的門框框口方位畫出線，標明尺度巨細,然后找工作人員設計出適宜的電動卷簾門(這兒值得留意的一點是框內高度比門扇的高度要高一點點)。

First, draw a line in the direction of the door frame opening of the required device, indicating the size, and then ask the staff to design a suitable electric roller shutter door (it is worth noting that the height inside the frame is slightly higher than the height of the door leaf).

把電動卷簾門的門框固定，這兒要先拆掉門框下部的固定板(留意:洞口兩邊地上要預留凹槽,經校對合格后,固定木楔,門框鐵腳與預埋鐵板件焊牢。

Fix the door frame of the electric roller shutter door. First, remove the fixing plate at the bottom of the door frame (note: grooves should be reserved on both sides of the hole on the ground. After verification, fix the wooden wedge, and weld the iron feet of the door frame firmly with the embedded iron plate).

裝置電動卷簾門扇主體門扇。一定要確保電動卷簾門與墻體結成全體，封閉性要做好,再粉刷洞口及墻體。粉刷結束后,門縫應均勻平坦,敞開電動卷簾門應當自由簡便,不得有過緊過松和反彈景象。

Install the main body of the electric rolling shutter door leaf. It is necessary to ensure that the electric roller shutter door is fully integrated with the wall, and the sealing must be done well before painting the openings and walls. After the painting is completed, the door seam should be even and flat, and the electric roller shutter door should be opened freely and conveniently without any signs of tightness, looseness, or rebound.

本文來自：濟南電動卷簾門安裝維修更多的內容請點擊：http://luoboyy.com我們將會為您提問的問題提供一個滿意的服務，歡迎您的來。

This article is from Jinan Electric Roller Shutter Door Installation and Maintenance. For more information, please click: http://luoboyy.com We will provide a satisfactory service for the questions you ask, and welcome you to come.